THIS IS
PARTS PAGE 3
Cylinder Head 8mm
mounting holes. Fits  Motors
using 8mm studs. Only $9.49
Intake manifold Gasket.
Extra Thick !!  Only $1.00
NT Carburetor idle
screw with tension
spring. Only $2.99
10 Pack of 6mmx1
standard mounting
nuts.  Only $3.99
10 pack of 6mm lock
washers. Use these to
keep your nuts where they
need to be!!! Only $1.99
CYLINDER HEAD WITH
6MM MOUNTING HOLES.
ONLY $9.49
SPARK PLUG TOOL DOUBLE
ENDED. FITS FACTORY ZL
PLUGS AND MANY OTHERS.
DUAL OR DOUBLE ENDED TO
FIT MORE SIZES. ONLY $3.99
GOTO PARTS PAGE 2
GOTO PARTS PAGE 4
GOTO PARTS PAGE 5
GOTO PARTS PAGE 1
GOTO HOME PAGE
GOTO PARTS PAGE 4
GOTO PARTS PAGE 5
GOTO HOME PAGE
THIS IS
PARTS PAGE 3
GOTO PARTS PAGE 2
GOTO PARTS PAGE 1
Engine Sprocket
Cover, 3 Hole.
Only $4.99
Rope Start. Fits Titan XC35 4
strokes and others using this
4 bolt Pattern. Only $24.99
Idler Wheel
Bushing Type.
Only $4.99
DAX F80  TOP END rebuild kit. Includes
47mm Bore Cylinder, Base Gasket, 47mm
Type S Piston and ring set, Alloy Head
Gasket, Alloy Head with extra large cooling
fins, Wrist pin, 14mm wide wrist pin bearing,
alloy intake manifold, exhaust gasket and
exhaust studs,  wrist pin clips. Fits Blocks
with 110mm Con Rods.  Everything you need
to make your top end new and fresh again !
Only $59.99
F80 TYPE S
PISTON
ROTARY VALVE THROTTLE
DIAPHRAGM CARBURETOR. Fits
Titan XC35, Honda GX35, Tanaka
3300.  Also will fit Honda GXH50 and
Titan XC50/S when using adapter
sold seperately.  Only $12.99
Includes O ring,
Primer bulb,
throttle stop,
and Thumb
Screws.  32mm
C to C bolt
pattern and O
Ring
OD=21.5mm
Diaphragm Carburetor Adapter Kit.
Mount the Rotary Valve Carb to your 4
stroke 50cc Titan or Honda with this
adapter kit.  Includes everything
except the Carb. No longer will you
need the tank to be higher than your
carb with this setup. Only $24.99
GOTO PARTS PAGE 6
MAGNETO MAGNET Super
strong  High Density !! Put that
fire back into your motor with
this new Magneto Flyweight
Permanet Magnet with Key way.
Only $4.99
DAX F80  Type S 38mm Stroke
BOTTOM END   Includes clutch,
High Power 312 Magneto,  
Balanced S crank,  M8x1.25
Sockets,

This is no Ordinary Block. This
Gen VII R Block has the New
Design Copyright Protected   
GP 360 Full Circle Steel Crank
Hand Drilled  and Balanced, 8.8
Automotive Grade Bolts for
engine Cases and Mounting
Studs.  Only $64.99
F80 S38
BLOCK
TYPE S
RT Carburetor Float.
Only $3.99
CLUTCH PUCK Square type.
15 is needed for a complete
set, or buy them single.
Only 0.25 cents each.  
Fuel Filter Clear
with Magnet.
Only $1.99
Magneto Grommet Nylon
Plastic Threaded. Only $1.99
WIRE CLIP. FITS PISTONS
WITH 10mm OD WRIST PINS.
Only $0.99 CENTS
TOP END INSTALL KIT M8 X
1.25P X 1.25P WITH DEEP
WELL CAP NUTS AND
WASHERS. ONLY $12.99
Rope Start Pull Rope
Starter 4 STROKE ENGINE.
Fits Titan XC50, Honda
GX50, Huaseng, and
others. Only $17.49
BICYCLE CENTER
STAND STEEL. WEIGHS
1.75 LBS. 100LB TEST.
ONLY  $8.99
DAX F80  Type S 40mm Stroke
BOTTOM END   Includes clutch,
High Power 312 Magneto,  
Balanced S crank,  M8x1.25
Sockets,

This is no Ordinary Block. This
Gen VII R Block has the New
Design Copyright Protected   
GP 360 Full Circle Steel Crank
Hand Drilled  and Balanced, 8.8
Automotive Grade Bolts for
engine Cases and Mounting
Studs.  Only $69.99

S40 GEN VII R BLOCK.
ONLY $69.99

S38 GEN VII R BLOCK.
ONLY $64.99
PISTON TYPE S 47mm
RAMPED AND SKIRTED !!  
POWER UP !!  ONLY $19.99
PISTON TYPE S 47mm
ONLY $9.99
Call !!